I also have the tag connector and I don’t get any connection to the board at all. Could you get a better picture of the the jumper cables at the and of the tag connector? I just want to compare it with my configuration.
Yes, this is my wiring.
Oh I thought this one would be the right pin for dtr… 
I also had DTR placed there but I got no connection between the box and my computer. So I assume that the pins are arranged like this
I’m really frustrated…now I’m getting a connection for a short moment and then this output.
cc3200tool -p COM5 --reset dtr list_filesystem
2025-01-10 22:21:09,230 -- Connecting to target...
2025-01-10 22:21:09,602 -- Connected, reading version...
2025-01-10 22:21:14,603 -- timed out while waiting for ack
2025-01-10 22:21:14,604 -- Could not connect to target: No ack for packet opcode=0x2f
Do you fix the tag connector somehow to get a stable connection?
Your toniebox is also connected to the powersource? That’s still necessary
Yep, I’m first connect the tag connector, than plug in the USB uart module and then connecting the toniebox with the DC cable.
First I connected the USB adapter to the computer. I entered the cc3200 command in the computer’s terminal and didn’t click enter yet. I also left the board in the white housing of the Toniebox and the Toniebox speaker plugged into the board. I placed the Toniebox loosely on the power connection of the Toniebox power supply. With one hand I pushed the tag connector through the debug port of the Toniebox. To prevent the Toniebox from turning or slipping away, I pressed it against the purple outer housing of the Toniebox as you can see on the image. While still pushing the tag connector into the debug port I made sure that the two LEDs on the USB adapter did not light up. After the green LED on the top of the Toniebox had stabilized, I used the index finger of the same hand that was still pushing the tag connector into the debug port of Toniebox board to press down the board into the power connector of the Tonixbox power supply.
If the Toniebox did not play the start melody, I pressed enter with the other hand on the computer and then the cc3200 command worked. If the Toniebox did play the start melody, I lifted the Toniebox from the power connection of the power supply and pulled the tag connector out of the Toniebox board. Then I tried again.
Hey, I have the same error message as you (No ack for packet opcode=0x2f).
If I put a bridge from VCC to SOP2 on the board of the box (as described in the instructions), then I get no connection to the box.
But if I set a connection from the UART VCC contact to SOP2, it starts the communication with the box, the box restarts and then the message “No ack for packet opcode=0x2f” appears.
Is it normal for the Toniebox to restart as soon as I start the command to read out the memory?
Hi. I had the same error as you.
Just check your cables.
document This is the documentation.
1 TX to RX (USB COM Controller)
2 RX to TX
3 and 9 (Interconnected VCC and SOP2)
4 RST to DTR
5 GND to GND
Set UART to 3,3 Volt!
After this i could use cc3200 tool instantly correct.
The UART Controller ist the same as you have at picture on the left side (it has 6 poles but you only need 4 of them!).
Except the use of the housing, I just did the same (today again, also with speaker for verification). But again I just keep getting the same output as above…it’s so frustrating…
Just to rule out anything else, I’m using this products:
Tag conncector: TC2050-IDC-NL CBL Plug-of-Nails 10-Pin-Programmierkabel - AliExpress 44
UART USB Modul: Hailege CP2102 USB zu TTL UART 232 485 Port Mutual Convert Adapter USB Serial Port Adapter 6 in One Multifunktionales USB Serielles Debug-Tool für Windows WinCE Linux Mac 32 64 : Amazon.de: Computer & Zubehör
Anything else that could be wrong?!
If I bridging 3 and 9 the Box doesn’t go green when plugged in to the power station.